Exhaust systems are integral to your ride’s performance; these amalgamations of piping, mufflers, and resonators carry exhaust gasses from your vehicle’s exhaust manifolds to the tailpipe. Dual muffler section upgrade designed to bolt up to the OEM midpipe   Features Bolts on to factory midpipe! 3-inch 304 stainless steel piping Dual high-flow mufflers with straight through... Reducing back pressure is the key to improving performance with a cat-back exhaust system. By allowing exhaust gases to exit the engine and flow through the system more freely, the engine runs more efficiently. This efficiency can translate to better throttle response, increased horsepower, and even improved fuel economy in some cases.

In this article, we are going to focus on cat back exhaust systems, and the main ten reasons that we have discovered as to why they are worth a look. If we know our car lovers, finding the right exhaust system for a car or truck is about getting more power without spending a fortune, and cat back exhaust systems tick a lot of boxes. Here is a pic of a converter and looking through the high flow core. Unleash the potential of your big displacement K motor with our high flowing 3" Header Downpipe.  This product eliminates BOTH OEM catalytic converters.  Available Catless or with a single High... We are proud to offer a wide range of completely custom, ready-built exhaust systems and parts at competitive prices with a lifetime guarantee. Contact Bradley’s Auto Service in Red Bank, NJ, today to get a quote for fitting, testing, and tuning your new exhaust system for maximum performance gains.

You’ll save right away when you add a front-pipe and a downpipe to your base system over buying each of these individually. Many car fanatics love a unique sound for their ride, almost similar to a racecar. It’s no secret that the standard vehicle exhaust system won’t produce a roaring or distinguishable sound. This is where a back cat exhaust system will be favorable to any motorist. The upgraded system will give you a more enjoyable, louder ride. But this is where certain systems will do better than others, so be sure to look into which one will be right for you.

Walker is your one-stop exhaust shop, offering a full line of mufflers, pipes, hardware and accessories. Cat to Y pipe intersection showing after cat O2 sensor location. This qualifies as one of the STRANGEST stock exhaust parts I have seen. For some reason Toyota/Lexus decided to weld a straight section of 60mm pipe to the cat outlet flange, angle cut it, weld a 50mm pipe pipe that has its last couple of inches expanded to 60mm and match angle cut. Also note the O2 placement is in the 50mm sections of the Y pipe where the sensor tip takes up a good portion of the available flow area.

This modification includes the pipes, muffler, and sometimes the resonator. The term "cat-back" itself signifies that everything behind the vehicle’s catalytic converter is being upgraded or replaced. Milltek's Sport Catback Exhaust Systems are designed to compensate for the sound reducing qualities from the particulate filter and significantly improve the sound aesthetic of the exhaust system.

At Thermal R&D Performance, we have been developing quality aftermarket exhaust systems for decades. The materials we use are generally an upgrade from OE metals, and we incorporate our True Helmholtz Technology to eliminate cabin drone. This eliminates unwanted sound without restricting airflow needed for improved performance. Some three-way catalytic converter systems have air injection systems with the air injected between the first (NOx reduction) and second (HC and CO oxidation) stages of the converter. As in two-way converters, this injected air provides oxygen for the oxidation reactions.

The bolstered heated front seats and contoured rear bench are upholstered in Onyx and Red leather. Appointments include a Blaupunkt 11-speaker sound system, a CD stereo, cruise control, a leather-wrapped shift lever, and automatic climate control. Whether you're seeking Upgraded Turbochargers, Axle-Back exhaust systems, Coilovers, or SubiSpeed Headlights we have you covered. The truck is based on the F-150 Lariat 4x4 SuperCrew and Shelby plans to limit production to 800 examples for the 2024 model year. Pricing starts at $130,000 for the naturally aspirated version and $139,995 with the supercharger attached. The urea solution is also referred to as diesel exhaust fluid (DEF).

But with so many options available, it's easy to get lost in the world of aftermarket exhaust systems. While some companies may try to lure customers with an attractive price tag or flashy branding, it's quality of performance, sound, and construction that truly sets a great brand like Invidia apart from the rest. Transform your vehicle with the Roush Performance F-150 Cat-back Exhaust System, an ideal replacement for your factory exhaust system. Crafted from robust, corrosion-resistant T-304 stainless steel, this system features high-flow mandrel bends to enhance exhaust flow efficiency. Experience the thrill of enhanced acoustics and performance with this premium upgrade for your F-150. Banks patented exhaust systems enhance power, fuel economy, and sound by removing all airflow restrictions.

Beyond these incremental advantages, there’s not much to tell cat-back and regular exhausts apart, as they are commonly made from the same types of materials in roughly the same shape. Most newer vehicles have electronic fuel injection systems, and do not require air injection systems in their exhausts. Instead, they provide a precisely controlled air-fuel mixture that quickly and continually cycles between lean and rich combustion. Depending on your make and model, cat back exhaust systems can lead to an increase in fuel economy. The engine doesn’t have to work as hard pushing exhaust gases through the piping which reduces its load and leads to higher efficiency and MPG. For car enthusiasts and performance drivers, upgrading the exhaust system of a vehicle is a no-brainer.

In 2010, most light-duty diesel manufacturers in the U.S. added catalytic systems to their vehicles to meet federal emissions requirements. Two techniques have been developed for the catalytic reduction of NOx emissions under lean exhaust conditions, selective catalytic reduction (SCR) and the NOx adsorber. Unleash your truck’s hidden potential by installing less restrictive exhaust components. Not sure what Invidia system you need or unsure if an Invidia USA exhaust is the best option for your Subaru, Mitsubishi, Honda, or Toyota? Shop Invidia on our site as well as other brands of exhaust systems and secure a high-quality exhaust system at our unbeatable prices. As far as sport compact enthusiasts are concerned, Invidia is a company that stands out in the crowd.

The amount of horsepower gained from installing a cat-back exhaust system varies by vehicle and the system’s design. However, when combined with other performance enhancements, the gains can be more significant. The primary goal of a cat-back exhaust is to reduce back pressure, allowing your engine to breathe better and operate more efficiently. The factory exhausts come in mandrel bent tubes made of stainless steel or aluminized steel. Besides offering longer durability, the construction also ensures there’s free flow of gases. To improve this, you can opt to replace some parts of the exhaust system using aftermarket performance exhaust systems.

Fine-tune your ride for the best performance and aesthetic today. Steeda offers the largest complete line of Ford-based parts and accessories for your build and is considered the largest privately owned 2011 ford f250 6.7 delete kit performance-based operation in the world. If you've been searching for the perfect place to purchase Ford automotive performance parts for your vehicle, then you're at the right place!

This quality material will ensure that your Cat-Back system will last through any harsh conditions. A cat back exhaust system is a form of car exhaust that includes the catalytic converter. This type of system is often used by those who want to improve their car's performance, as it can help to increase power and efficiency.

Our straight-through brushed-finished mufflers are configurable to your desire, smoothing the exhaust note to a deep growl, without adding restrictions, rasp or drone. Strong high-quality bracketry and OEM-style clamps hold the system steadily in place, making the install or removal a snap, and fitment simple, yet precise. A cast 3" to dual 2.5" rear splitter creates an ultra-smooth transition, steadily feeding exhaust gasses out of the system, while looking tidy from under the rear bumper. Finally, removable 4" polished slash-cut exhaust tips finish the system, adding a classy motorsport-inspired touch to the rear of the vehicle. In addition to high-quality materials and components, the design of each high-performance exhaust system allows for easy, bolt-on installation right out of the box. CORSA exhausts require no welding and can mount directly to your factory connections.

The installation of a cat-back exhaust system is fairly easy, but this too depends on your vehicle’s make and model. But, compared to the alternative, they are the easiest way of improving your vehicle’s performance without breaking the bank. As a result, the engine gets to breathe better and so release more torque and horsepower.

A faulty exhaust system can cause a decrease in power, acceleration and fuel efficiency, as well as potentially exposing drivers and passengers to harmful gases, so issues should be fixed immediately. We have a wide range of exhaust systems in stock – browse our range and find the correct exhaust system for your car below. There are many distinct and differentiable features to each of many cat back exhaust systems, meaning it’ll be easys to find a do-it-yourself cat back installation. The modifications directly bolt where the original exhaust is, so there won’t need to be excessive installation. You’ll have everything you need to replace the exhaust with the pipes, muffler, and tips that come with a DIY package.

Shelby also gives the truck some off-road chops by installing a BDS 3.0-inch lift kit, Fox 2.5-inch internal bypass dampers, and performance rear traction bars. The truck also sits on a set of 22-inch Shelby wheels wrapped in 35-inch all-terrain tires. The new 2024 Ford Shelby F-150 packs up to 785 hp, or more power than many supercars. That's with an available supercharger for the truck's 5.0-liter V-8. Buyers can also opt for a naturally aspirated version where the V-8 keeps its stock 400-hp rating.

We use the latest, advanced equipment to ensure precise and accurate adjustments. Each of the trucks will be included in Shelby's official registry. Revology's '68 Shelby GT500KR surpasses the performance of the original with a 710hp supercharged 2008 ford f350 6.4 egr delete kit/Roush Performance 5.0L Ti-VCT Coyote DOHC V8 engine. In 1962 Carroll Shelby, one of America's greatest race car drivers began a new chapter in his storied career with the legendary Cobra sports car. A piece of of this sports car's "DNA" is part of every subsequent Shelby vehicle.

A stock system is designed to reduce and if possible eliminate all the noise produced by your vehicle. Because of this, the axle-back exhaust system does not impact the flow or pressure of the exhaust gases in any way. The axle-back exhaust system uses the factory exhaust pipe which does not have a large diameter. This offers even more breathing space for the engine thus better performance. Most cat-back exhaust systems are customized and not universal. One is to replace specific parts like with cat-back exhaust systems.

Finally, the catalytic converter can become fouled over time, resulting in a loss of power. This can be remedied by having the converter cleaned or replaced as needed. When it comes to choosing the right cat back for your car, there are a few things you need to keep in mind. First, you need to make sure that the cat back you choose is compatible with your car's make and model. Are you an aggressive driver who likes to take corners at high speeds?

Even a small leak can cause problems down the line, so it's better to be safe than sorry. By following these simple tips, you can ensure that your cat back installation goes smoothly and without any issues. When it comes to cat back installation tips, there are a few things you need to keep in mind.

It typically includes a rear pipe, resonator, and muffler that all attach after the last catalytic converter. The turbo-back system is the most complete system you can buy. It replaces all of the components that the previous two systems that we’ve talked about and also upgrades the downpipe. The downpipe is the first piece of exhaust piping that comes after the turbocharger and it also houses the catalytic converters on all L15 powered 1.5T Civics and Integras. From a sound and performance perspective, you’re going to get the most of both compared to the other two versions mentioned before.

By freeing up the restrictions in the exhaust system, a cat back exhaust can help your engine to breathe more freely. This, in turn, can lead to a significant increase in horsepower. If you love cars just as much as we do, then you know that one of the best upgrades you can make to your vehicle is a cat back exhaust. But if you're not familiar with this term, don't worry – Vandemon Performance is here to break it down.

The performance parts available at Steeda include lowering springs, wheel spacers, spark plugs, brake kits, and many more. Choose from our Ford automotive parts today so that you can keep your ride in great condition. When it comes to picking a cat back exhaust system, you will likely be choosing between stainless or aluminized steel. The majority of the performance systems are made from stainless steel which is favoured as they won’t oxidize and corrode over time like traditional steel can.

Your engine’s performance and acceleration are then increased. The mandrel-bent tubing reduces the level of back pressure in the exhaust manifold as the larger diameter reduces restriction to the flow of exhausts. REMARK is an exhaust system manufacturer specializing in producing high quality, hand crafted exhaust components and systems for a range of vehicles. All products are made from 304L "Aircraft" Grade stainless steel. Milltek's 3.15" (80.00mm) Sport Catback Exhaust System has multiple tip options in Polished, Cerakoke Black, Brushed Titanium, Burnt Titanium and Carbon fiber. You get the only the best with SPD's 3" resonator delete pipes. These 304 stainless steel pipes are ..

To make a very long story short so far so good I’m happy with the product. I had 1 dinged tip out of the 4 that prob happened during shipping n y’all already have a new replacement tip on the way so customer service is great as well. Only thing I would change as previously stated would be a little more noise but again that wasn’t my main goal to being with. Hats off to what y’all do and please make more B9 Audi S4 parts n I’ll happily buy them. I regret not buying the IE intake but hey sometimes we all make poor decisions lol. Every vehicle-specific CORSA product is engineered and designed to match the unique properties of the vehicle it is designed for to deliver perfect fitment and performance.

CORSA does not recommend or recognize purchases and installations on unspecified vehicles. ARK Performance is a leading manufacture that develops the best cat back exhaust systems, downpipes, test pipes, and hi-flow cats for all car enthusiasts. Using custom designed straight through mufflers for flow - without the noise level of a track car. From a company that’s as committed to your satisfaction as to sonic excellence. A catback exhaust system is a great way to improve the sound, performance, and emissions of your vehicle. If you are looking for a way to improve your vehicle, a catback exhaust system is a great option.

Finished in Panther Black Metallic over Onyx and Red leather, the car is powered by a 6.2-liter V8 linked with a six-speed automatic transmission and a limited-slip differential. Purchased by its current owner in February 2022, this G8 GXP is now offered with a reproduction window sticker, service manuals, a car cover, the removed exhaust system, a spare set of wheels, and a Michigan title. A catalytic converter is an exhaust emission control device which converts toxic gases and pollutants in exhaust gas from an internal combustion engine into less-toxic pollutants by catalyzing a redox reaction. Catalytic converters are usually used with internal combustion engines fueled by gasoline or diesel, including lean-burn engines, and sometimes on kerosene heaters and stoves. Whether you’re accelerating up a highway on ramp or passing slower traffic, improved acceleration lets you get up to speed more quickly. Gain horsepower, increase torque, and give your truck a more aggressive exhaust note with a new exhaust system.

Once we receive and evaluate your OEM catalytic converter, refunds will be issued in the form of a MagnaFlow Visa® Prepaid Card valued up to $75. A Recycling for Refunds icon will appear in your cart to get the process started. Sign up for our newsletter to be the first to know about our latest products, offers and events at MagnaFlow.

There is a range of muffler types you can choose from with a cat back exhaust system with most people opting for a glasspack or straight-through muffler. Both of these options are designed to work well within the system to reduce back pressure. Deciding to purchase a performance exhaust system for your car is no easy task.

You can also add other upgrades to give your Charger an extra performance boost. Visit the AmericanMuscle headers and exhaust accessories pages to find parts that fit your new cat back system. Mishimoto offers a wide selection of exhaust systems, including cat-back exhausts, performance exhaust systems, and aftermarket exhaust options, designed to enhance your vehicle's performance, sound, and style. Our exhaust systems are engineered with precision and constructed using high-quality materials to deliver improved exhaust flow, increased horsepower, and an enhanced driving experience. Enhance the sound and performance of your Subaru with our premium cat back exhaust systems. Designed to replace the factory exhaust system from the catalytic converter rearward, these cat back exhausts offer a deeper, more aggressive exhaust note while reducing restriction for improved airflow.

Our design concept is to provide a sporty and authentic exhaust note, while improving performance, and enhancing the visual styling of your vehicle. Each product is carefully developed, and then expertly crafted by our own factory. The whole reason I decided on an IE cat back vs mbrp or AWE was the craftsmanship. However I do live in warm and sunny south Florida so I know it will only see tons of rain but never salt or snow unless it’s an impromptu trip. I love the lil burble crack when going down in rpm and down ship. I wish it were a little louder but if that we my main goal I’d have just gutted cats n resonators n left stock mufflers.

The difference is that the dual exhaust system has two exhaust systems on one vehicle. Meaning, when modifying your exhaust, never start from the front of your turbocharged vehicle with a downpipe or with headers on your naturally-aspirated platform, you will create a bottleneck in the flow. By starting with a cat-back first, your exhaust gases will flow more freely if the rest of your system is stock.

All performance exhaust systems are designed with you in mind, and we cater to an ever-expanding range of vehicles. Milltek believes in continuous evolution, and their research & development team work throughout the year to deliver the most in demand solutions to all your performance exhaust requirements. All products are made in the UK and distributed to more than 90 countries worldwide, making Milltek Sport one of the most accessible performance aftermarket brands on the market. If you're looking to customize your vehicle's exhaust system, Mishimoto also offers a range of aftermarket exhaust options. These exhaust systems are designed for specific vehicle models and provide a combination of performance, sound, and visual enhancements.

It's more than our precision-fit or full engine-to-tailpipe product offering, Walker sets the standards. From mild rumble to wild roar, upgrading your exhaust will improve the sound of your truck and help it to stand out from the pack. This direct-fit SPEQ Series system bolts on to your Tacoma easily thanks to the extensive use of 3D scanning during development to ensure OEM-like fitment.

This style of clamp design is popular in high-end OE applications and is known for long-term reliability. You can change the look of your Jeep too, with everything from polished stainless steel to full black exhaust kits, you can pick just the right look for your jeep. Depending on the year of your Jeep you might even be able to get a single or dual exit exhaust. You can choose your favorite exhaust system from our three collections, the GRiP Exhaust, N-II Exhaust, or the DT-S Exhaust.

Catback exhaust systems are popular among car enthusiasts because they can improve the sound and performance of a vehicle. From classic American muscle cars to the newest off-road capable rigs, STILLEN has you covered. Browse our most popular performance car, truck and SUV exhaust systems to find the ultimate exhaust experience for your vehicle. If you’re looking to enhance the performance of your car, you may have heard the term "cat back exhaust" being thrown around and wondered what is a catback exhaust exactly.

This will improve the throttle response and acceleration in naturally-aspirated cars. The same reaction will be found in cars with forced induction with the addition of less turbo lag or supercharger response. Cat-Back exhaust systems are the most popular, coveted, and sought-after modification that enthusiasts will initially perform because of the main reason, and that is the sound. All of the brands we carry offer exhaust systems that are the result of decades of research and development.

When it comes to improving your vehicle’s performance, you have two options. However, stainless still can be very expensive, as opposed to aluminized steel which is very affordable. It is also resistant to corrosion, just not to the level of stainless steel. Since there is no back pressure and the diameter is large enough, the engine will not use a lot of energy to push the exhausts out. While getting a cat-back performance exhaust system can be pricier initially, it can save on a lot of costs in the future. These exhaust pipes are usually wrapped in sound-absorbing materials, mostly fiberglass packing.

Since 2003, we have specialized in building BMW M-models (and Tesla) with a refined selection of industry-leading, high quality products. Our 8,000 sq/ft installation facility and shipping headquarters is located in Anaheim, California. IE's advanced DroneTrap technology captures the pulse waves responsible for your B9 3.0T engine's exhaust note and draws them into dual mathematically tuned resonators. The internal ports are engineered to resonate these waves against each other in a process that selectively cancels out those responsible for annoying drones.

If you have modified your 4×4 with lifted, lowered, or air type suspension systems, you can opt for a specially designed cat-back system with more pipe curvature before the rear axle. This is necessary for off-roading as it allows a higher degree of wheel travel and greater clearance for reduced-height springs and airbag suspensions. The custom exhaust systems available let you pick from a selection of pipework that allows you to adjust the exhaust to suit your noise preference. Are you looking to boost the power and efficiency of your vehicle?

Decades later, Gale and the team are not only innovating, patenting products, and setting the bar for aftermarket performance manufacturers, we're also sharing our secrets with the world. The 6.2-liter LS3 V8 was factory rated at 415 horsepower and 415 lb-ft of torque. It is used to expel harmful gases and substances from your engine; without it, the car could experience a build-up of fumes.

In addition, a cat-back exhaust can also improve your car's fuel economy. So, if you're looking for a way to get more out of your car, a cat-back exhaust is a great option. We now offer Maverick cat-back exhausts in both all-wheel drive (AWD) and front-wheel drive (FWD) configurations.

Combined with our five different tip options, we've got you covered. We’ve had decades of experience perfecting exhaust style and technology and have developed custom exhaust systems considered too ‘niche’ by competitors. Many exhaust manufacturers use 400 series stainless steel to reduce costs and pad their profits. Additionally, the Maverick systems by Thermal offer a range of upgraded tip options that owners can choose from or change over time. Getting an upgraded cat-back exhaust system for your truck can enhance your performance and produce a great sound. Then there’s poor fitment and the dreaded drone that all too often accompanies aftermarket exhausts.

From Overland Series to our all-new SPEQ Series, explore MagnaFlow's latest performance exhaust systems designed for the 2024 Toyota Tacoma. Aftermarket cat-back exhaust upgrades are a relatively simple way to increase your vehicle’s power. Typically these upgrades involve installing wider piping with fewer sharp or sudden bends as a way to reduce backpressure. Backpressure is pressure opposing the desired flow of exhaust gasses. The more you are able to reduce backpressure, the more efficient the system will be, and ultimately your horsepower will increase. Cat-back exhaust refers to any part of the exhaust system that’s behind the catalytic converter.

Federal Catalytic Converters are not legal for sale, installation or use in the state of California. It should be noted that a split system will often provide an aggressive noise increase, and some designs will split the two pipes to opposite sides of the vehicle. If you are looking to save a little money but still get most of the benefits of a cat back exhaust system, however, aluminized steel may be the way to go. Made from traditional steel that’s been coated on all sides with aluminum-silicon alloy, these systems are very strong thanks to the metallurgical bond which still provides a level of corrosion resistance. While the aluminum coating reflects heat well, the steel can corrode if the aluminum layer is chipped or scraped off. Most cat-back systems will come in either an aluminized or stainless steel version.

A spare set of 19″ Y-spoke alloy wheels is included in the sale, and they are shod with Bridgestone tires. The car is finished in Panther Black Metallic (80U) and features a GXP-specific front bumper cover and rear diffuser as well as a sunroof, fog lights, dual hood scoops, fender vents, and a rear spoiler. Imperfections are noted on the decklid and on a door and are also shown in the gallery. Our expansive inventory of Subaru performance parts ensures your vehicle not only performs at its peak but is also supported by our unparalleled customer service. At SubiSpeed, we understand that upgrading your Subaru is not just about selecting the right parts; it's about having a trusted partner every step of the way.

From the inception of the small block Cobra, Carroll Shelby intended to build a race version of his lightweight roadster; its ultimate iteration was the 289 FIA roadster. Special Edition Shelby F-150 Super Snake celebrates Carroll Shelby's passion for performance trucks. Shelby American is celebrating the 100th anniversary of Carroll Shelby's birth with a performance street truck to honor the ledged.

Shelby American is proud to announce the latest generation Shelby Ford F-150 Raptor, the most polished off-road truck ever we have offered. Add more products to wishlist by simply getting registered on Eurocarparts. One of the most important elements of your car, your exhaust is vital for preventing harmful gases from being released into your surroundings. When you notice damage or wear and tear, it's essential to fix them quickly.

There are several factors to consider when selecting an exhaust system for your vehicle, including noise level, finish, price, style, and installation difficulty. As you move through the versions here, you’ll notice that the more complete the system, the more expensive it becomes. In exchange, you'll get more performance and sound benefit out of the system. To sweeten the pot, our exhausts come with significant savings once you start bundling multiple pieces together.

Most designs of the time therefore included secondary air injection, which injected air into the exhaust stream. This increased the available oxygen, allowing the catalyst to function as intended. Cat-back exhaust systems replace every component behind the catalytic converter, including most piping, mufflers, resonators, and tailpipes.

The products of REMUS Innovation Forschungs- und Abgasanlagen Produktions GmbH („REMUS") are distributed worldwide. This applies equally to products approved in Austria, which are subsequently manipulated, modified, edited or otherwise interfered or changed by the respective buyer, so that it no longer has its original condition. Discover MagnaFlow's latest evolution in performance exhaust technology. Stainless steel is the most popular choice for cat backs because it is durable and has a deep, throaty sound. But if you're looking for something lighter weight, you can also find cat backs made out of titanium. So, when it comes time to choose the right cat back for your car, keep these three things in mind and you'll be sure to find the perfect fit.

They both improve your engine’s tone and give it that deep rumble loved by every motor enthusiast. Getting a cat-back exhaust system is definitely the more budget-friendly option. Other benefits of aluminized steel is they are lightweight and very workable.

Let’s look at the top ten reasons why a cat back exhaust system may be right for you. While a cat-back exhaust system includes all components from the catalytic converter to the exhaust tips, an axle-back system only replaces parts from the rear axle to the tips. Axle-back systems are generally easier to install and less expensive but offer more limited performance improvements and sound changes compared to cat-back systems. All our performance exhaust systems are designed with you in mind, and we cater to an ever-expanding range of vehicles. We believe in continuous evolution, and our research & development team work throughout the year to deliver the most in demand solutions to all your performance exhaust requirements.

Because the engine won’t generate as much fumes and doesn’t need to work as hard to eliminate or minimize the fumes, your car will run better, saving you mileage. A benefit like this will improve the longevity of your car and even save you money at the gas pump. At Bradley’s Auto Service in Red Bank, NJ, we can build a completely custom exhaust system for your vehicle, including cat-backs. We will work with you to create your exhaust exactly the way you want it, with any combination of look, sound, feel, power, or muffler at your fingertips.

It is called a "catback" system because it starts at the catalytic converter, which is located in the middle of the exhaust system, and continues to the tailpipe. With an aftermarket performance exhaust system from CORSA, you'll be able to lose yourself in rich, deep exhaust notes you can feel in your chest with every drive. It doesn't matter if you're behind the wheel of a BMW, Charger, F-150 or Wrangler, you can choose from our sport, touring or extreme sound level performance exhaust systems for the sound that suits your tastes best. By allowing your engine to run more efficiently, a cat back exhaust can help you to save money at the pump. As an added bonus, cat back exhaust systems often produce a deep and throaty sound that many car enthusiasts find appealing. Cat-back systems usually have the option or glasspack or straight-through mufflers, which are designed to work with the other system components to reduce back pressure.

We want to make sure the part fits your specific vehicle so we need a little more information from you. You can find out by inspecting the emissions sticker that is located in your engine compartment.

Cat-back exhaust systems will include any pipes that run from the catalytic converter to the muffler, the muffler itself, any pipes that may run from the muffler to the exhaust tips, and the exhaust tips themselves. Some cat-back exhaust systems have a muffler 2011 f250 egr delete kit, which means no muffler is included. This is typically found on vehicles that function primarily for off-road use; it's not standard on daily driver vehicles and is even illegal in some states.

You also need to be careful when tightening the bolts on the cat back. Over-tightening can damage the system, so just make sure they're tight enough to hold everything in place. It's important to make sure that the cat back is properly aligned with the exhaust pipe. If it's not, you could end up with an inefficient or even dangerous exhaust system. Competitors often rely on generic silencers or gimmicks that claim to cut out drone without any real knowledge or development involved.

Cat-back exhaust systems replace all the components after the catalytic converter, sometimes referred to as the cat. Now you can upgrade your downpipe or mid-pipe depending on your applications. Some cat-back systems will include a mid-pipe depending on your cat layout. And when you want to make more power and take your vehicle to the next level, then you will be ready for an exhaust manifold. Available only from Mallett Performance Cars, this exhaust system is made from 304 stainless steel and features the highest quality mufflers and resonators.

Choose ARK and you will not be disappointed with the sound and quality of our products. Installing a catback exhaust system is a relatively easy task. However, it is important to follow the instructions that come with the system. If you are not comfortable installing the system yourself, you can take it to a qualified mechanic. Get an exclusive inside look at what we are doing on a daily basis with Banks’ Insider News.

The 2024 Roush Super Duty stands as a testament to Roush Performance's dedication to engineering excellence, blending raw power with refined style. Whether it's for work or play, the Roush Super Duty promises to deliver an unparalleled driving experience, making every journey memorable. If the above ten reasons to consider a cat back exhaust system have you thinking it may be right for your car then Sandgate Auto Electrics are the people to call. Your neighbours may disagree that this is a benefit, but as we’ve mentioned earlier, and depending on your muffler choice, your vehicle will have a lot more grunt. This may well be the area you need to do the most research into and the sound quality, and type, can range drastically per system. At Walker, it's more than peace of mind in knowing we lead the industry with unparalleled level of compliance.

Automotive Performance Systems Inc. (APS) and its NEUSPEED®‚ and Neumann Distributing divisions are your number one source for aftermarket import performance products! We carry a large inventory of all the parts featured in our catalog and on our website. Our customer service is unrivaled, with the most knowledgeable support team in the industry. All aFe exhaust systems are engineered and manufactured in our Corona, California facility. The price of a cat back exhaust system can vary widely depending on the make and model of your vehicle, the materials used, and the complexity of the design.

These look like standard mufflers with a VERY unusual side entry rear exit configuration. Notice the heat discoloration at the intersection where the split occurs.Heat discoloration shows up where there is a flow restriction. Notice also the heat discoloration just after the pipes enter the silencers. It is AMAZING the engine makes the power it does through this congestion. Features Only 10 lbs [catless and non resonated version] 304 stainless steel piping Smooth air flow for maximum horsepower Compatible with both manual and automatic transmissions TIG welded to perfection... The main functions of exhaust systems are increasing horsepower and improving your engine sound.

You get the only the best with SPD's 3" resonator delete pipes. These aluminized steel pipes are 3" .. SPD's high performance resonator cat-back pipe replaces your factory resonator pipe with a true 3" p.. The welds and craftsmanship are top notch, and the tips look perfect.

Noticeable gains will be noticed in the initial throttle response, with reduced turbo lag. Engine movement and exhaust weight are transferred into the exhaust hangers, which puts a lot of stress on the mount brackets. IE's catback system is manufactured with multi-point and boxed-in hanger mounts designed to stand the test of time. Drive confidently knowing your exhaust is securely mounted and protected against annoying rattles or breaks. All piping is constructed of mandrel-bent T304L stainless steel to offer superior corrosion resistance.

This exhaust is going to sound the deepest and give you some nice pops and bangs, while also giving you real world WHP and TQ gains. We’ve seen as much as +12 WHP when we tested our turbo-back for the 2022+ Honda Civic! For this version, we do recommend a tune and a device like a Ktuner V2 or Hondata Flashpro to take full advantage. Since the OEM catalyst is replaced with the downpipe, the Turbo-back system is sold for Race Use Only. A cat-back exhaust system replaces the stock exhaust components from the catalytic converter back to the exhaust tips.

They directly bolt on to where the original exhaust sits and do not require any further modification. Cat back exhaust systems come with exhaust pipes, muffler and exhaust tips, so you have everything you need to replace the exhaust. The cat back is the section of the exhaust that runs from the outlet of the catalytic converter to the exhaust tips. Exhaust systems that include this often feature a large pipe running from the converter to the muffler, with mandrel-bent turns and glasspacks for reduced back pressure. Your go-to spot for information on the exhaust system, as well as mufflers, catalytic converters, pipes and sensors.

Advanced 3D scanning tools and cutting-edge software provide our engineers with a high-resolution digital model of the Audi B9 S4 chassis. This data is then used to maximize the exhaust size for flow and optimize all available space for the perfect catback fitment. CORSA branded exhaust systems are backed by a Limited Lifetime warranty for as long as you own your vehicle with proof of purchase. The new exhaust sounds perfect, a marked improvement over stock. It is not too loud - I use the car as a daily driver and drive in capital beltway traffic.

A cat back exhaust system, also known as a catback exhaust, is an aftermarket automotive exhaust system that replaces everything in the exhaust system from the catalytic converter to the tailpipe. Cat back exhausts are available in various configurations and materials, allowing drivers to choose the one that best suits their needs and preferences. An aftermarket cat back exhaust might be the perfect upgrade that can enhance your Dodge Charger’s performance and road presence. Unlike its OEM counterpart, it boasts a less-restrictive construction, so it can release more exhaust gases. A cat back exhausts is also designed to install behind a catalytic converter, so remains emission compliant. In addition, its design lets your vehicle generate a more distinct exhaust sound.

Next we have the option we refer to as the Cat-back system (sometimes also known as "with Front Pipe" exhaust). One of the most noticeable changes after installing a cat-back exhaust system is the sound. The exhaust note becomes deeper and more pronounced, giving your vehicle a more aggressive tone. The specific sound varies depending on the muffler and pipe design, allowing drivers to choose a system that matches their preference for loudness and pitch.

Our exhaust system uses larger piping compared to the factory exhaust system, yet weights 5 lbs. The factory system uses 2.56" piping, which reduces to 2.36" before splitting, greatly diminishing the overall diameter of the system. Finally, our system’s 4" exhaust tips dwarf the factory 3.15" tips, giving the rear of the vehicle a sportier look. Beautifully hand-crafted T304-stainless-steel components adorn the system with stunning TIG-welding throughout.

Aftermarket custom cat back exhaust systems increase the efficiency of an exhaust system because of the mandrel-bent turns and reduction in back pressure. They are the popular choice when it comes to aftermarket exhaust systems as they offer reliable performance and sound without having to buy a new catalytic converter. They are also well-suited to those who like to handle their own installation!

As an added bonus, cat-back systems include all of the necessary parts to replace your existing exhaust. The only costs you need to worry about are the kit itself and installation. Installing one of our cat-back exhaust systems is one of the best upgrades you can do on your Ford Maverick. Cat-back exhaust refers to what's in "back" of the "cat," or catalytic converter. It refers to the components that run from the rear outlet of the catalytic converter all the way back to the exhaust tip.

Follow us on Facebook, Instagram, YouTube and Twitter to stay up to date on our latest products, projects, and adventures. Join the conversation and show off your ride with #MagnaFlow for a chance to be featured. Overall, cat back systems are relatively low-maintenance and easy to keep in good working order. There are a few common problems that can occur with cat back systems, but fortunately, they are relatively easy to fix.

If you've got questions about cat-back exhaust systems, pipe diameters, muffler type, or anything else, talk with our product specialists. All 1995 model year vehicles, and all 1992 model year or earlier vehicles. All model year vehicles that were manufactured with EPA or Federal emissions certification. Exhaust gases from the cylinders are collected in the exhaust system to prevent harmful fumes from entering the vehicle.

Take up to $150 off gas truck exhaust and up to $75 off diesel truck exhaust and components starting July 1st, 2024 – for a limited time only. Evidently, a cat back exhaust system has many benefits all while being a quick, easy, and affordable solution that will transform your car. If you have any questions about what a cat back exhaust system can do for you, don’t hesitate to contact us at Loper’s Performance Center.

Featuring virtually indestructible 100% stainless steel, our patented TorqueTube headers maximize exhaust extraction to haul you up the grade. This Takeda cat-back exhaust system by aFe POWER delivers superior performance, quality, and good looks. By replacing the rear section of your exhaust with a quality cat-back car performance exhaust system, you can reduce the backpressure and allow your engine to cycle with more speed and efficiency. Thanks to their larger diameter pipes and high-quality mandrel bends, a good cat-back exhaust system will increase the efficiency of your car’s exhaust system, and with increased efficiency comes increased power. The exhaust system in your car directs fumes away from yourself and your passengers, improves engine performance and fuel consumption, and controls cabin noise.

And a lot of people think that gearheads mess with it just to make our cars sound louder. Another problem is that the gaskets and seals can degrade over time, resulting in leaks. These leaks can usually be fixed by replacing the relevant seals and gaskets.

Namely, it replaces the rear axle-back and tips and then a portion of what we refer to as the mid-pipes. This system is emissions friendly and doesn’t require any tuning. In New Jersey, vehicles must pass emissions testing to ensure they meet environmental standards. Since cat-back exhaust systems do not modify the catalytic converter or engine management system, they generally do not affect a vehicle’s ability to pass emissions testing.

There are subtle changes on the outside to let onlookers know that this is no ordinary F-150, such as a custom dual-intake hood, a custom front fascia and grille combo, and Shelby badging. For the interior, Shelby adds carbon-fiber trim, billet racing pedals, custom floor mats, and a serialized plaque. For lean-burn spark-ignition engines, an oxidation catalyst is used in the same manner as in a diesel engine. Emissions from lean burn spark ignition engines are very similar to emissions from a diesel compression ignition engine. Upon failure, a catalytic converter can be recycled into scrap.

CORSA exhaust parts, hardware and detailed instructions are included in each kit so you can get on the road as fast as possible. We hope this article has provided a thorough answer to the question of what is a catback exhaust and provided advice on how they can help improve the performance of your car. While they may not provide a big performance boost for all cars, cat-back exhausts are a simple and effective way to improve gas flow in your exhaust system beyond what stock exhausts are capable of. Catalyst poisoning occurs when the catalytic converter is exposed to exhaust containing substances that coat the working surfaces, so that they cannot contact and react with the exhaust. The most notable contaminant is lead, so vehicles equipped with catalytic converters can run only on unleaded fuel.